Mas Maya Coating is thin and expressive — every detail shows.

To achieve a flawless result, your surface must be: Flat, smooth, clean, dry, and stable.

Steps:

• Remove loose paint, tiles, plaster, and fittings.
• Fill cracks and imperfections deeper than 3mm using Mas Maya Prep.
• Level textured surfaces (like tile joints or popcorn finishes) with Mas Maya Prep.
• Clean thoroughly with a damp cloth and remove all dust.
• In wet areas, make sure a waterproof membrane is intact before coating.
• Protect edges and floors with low-adhesive masking tape, leaving a 4mm gap from the surface for a clean finish.

Primer creates a strong bond between the surface and Mas Maya Coating.

Steps:

• Stir thoroughly before use.
• Apply a thin, even layer with a short-pile roller (4 mm) or brush.
• Avoid puddles or thick areas.
• On very absorbent surfaces, lightly mist with water first.
• Allow to dry for at least 30 minutes (and no longer than 24 hours) until slightly tacky.

Correct mixing ensures a smooth texture and consistent colour.

Water ratios:

• Walls and ceilings: 330 ml water per 1 kg of powder
• Floors: 400 ml water per 1 kg of powder

Steps:

• If using a colour other than Natural or Clay, dissolve the correct amount of pigment for your chosen colour into the water first.
  
• Slowly add the Coating to the water (never the other way around).
  
• Mix gently with a handheld plaster mixer — avoid high-speed drills.
  
• The mixture should be smooth and creamy, like yogurt.
  
• Let it rest for 15 minutes, then mix again before applying.
  
• Keep batch sizes consistent to maintain colour uniformity.

The base layer provides structure and embeds the Mas Maya Mesh, which is recommended for most installations — especially floors, tiles, wood, pools, or any surface with joints, cracks, texture, or movement.

Steps:

• Apply a 2.5 mm layer of Mas Maya Coating using the toothed side of a 5 mm toothed trowel.
  
• Place the Mas Maya Mesh on top, leaving a 1 cm gap from edges and overlapping sheets by 10 cm.
  
• Press the mesh into the coating, starting from the top, using a flexible or steel trowel.
  
• Smooth over with a flat-edged trowel until the mesh is barely visible.
  
• Allow to dry until firm (the surface shouldn’t indent under light pressure) or leave to dry fully before applying the finishing layer.

This is the final visible layer that defines the look and texture of the surface.

Steps:

• Apply a 1.5–2 mm layer of fresh coating with a clean steel trowel.
• Use smooth, overlapping strokes and keep the trowel edge clean to prevent drag.
• Work wet-into-wet to avoid visible join lines.
• Plan ahead to finish entire sections at once — stopping mid-surface can leave visible lines.
• Wherever possible, work to the edges of a surface for a seamless result.

Smoothing and polishing close the surface pores and create the final texture. Begin only when the coating is firm and no longer changes under light pressure (around 15–20% moisture if using a meter).

Steps:

• Lightly mist the surface with clean water.
  
• Optional: Add a small amount of coconut soap to the spray for a creamier texture.
  
• Glide the Mas Maya Foam Float over the surface in circular strokes until a fine surface cream appears.
  
• If the float sticks, mist a little more water.
  
• Using a flat-edged steel or plastic trowel, spread and press the surface cream to fill small holes, remove excess material, and flatten the finish.
  
• The final surface should feel smooth, polished, and even to the touch.

Mas Maya Presealer is a water-based, breathable layer that locks in the colour of the coating, seals open pores, and prepares the surface for Sealer.

Skipping this step will cause the colour to darken and absorb unevenly.

Steps:

• Ensure the Mas Maya Coating is fully dry, clean, and dust-free before applying.
  
• Stir thoroughly before use. Do not dilute.
  
• Apply a thin, even coat with a short-pile roller (4 mm) or brush, working systematically across small sections.
  
• Avoid puddles or heavy build-up. Use a brush for edges and corners.
  
• Allow to dry for about 2 hours, then apply a second thin coat.
  
• Let the Presealer dry completely (around 2–3 hours, depending on conditions) before applying the Sealer.
  
• Clean all tools immediately after use with water.

Mas Maya Sealer is a two-component polyurethane system that protects and enhances Mas Maya Coating with a matte, durable, and waterproof finish — ideal for high-traffic or moisture-prone areas.

Always apply Presealer first to preserve colour and ensure even absorption.

Steps:

• Confirm the Presealer is completely dry, and the surface is clean, dust-free, and stable.
  
• Shake Component A, then mix 5 parts Component A with 1 part Component B. Stir slowly until fully blended and let rest for 5 minutes.
  
• Use the mixture within 60 minutes (pot life).
  
• Pour into a clean paint tray and apply a thin, even coat with a short-pile roller (4 mm), brush, or spray gun.
  
• Immediately follow with a clean, dry roller to remove excess and prevent shiny spots or stains.
  
• Allow to dry for at least 8 hours before applying the second coat.
  
• Mix a fresh batch using the same 5:1 ratio and apply the second coat in the same way.
  
• The surface will be touch-dry in 8–12 hours and fully cured after 72 hours. Avoid water or heavy use during this time.
  
• Clean tools immediately after use with water and discard any leftover mixed sealer.

Tips:

Apply thin, even coats and always use a second dry roller to remove excess. For high-traffic or exterior areas, finish with Mas Maya Heavy-Duty Sealer for extra protection.

Mas Maya Heavy-Duty Sealer is a two-component, solvent-based polyurethane system made for high-traffic and high-exposure areas. It offers exceptional resistance to abrasion, chemicals, moisture, and UV — ideal for floors, steps, exteriors, commercial spaces, and pools.

Always apply Presealer and Sealer first to maintain colour and ensure even absorption.

Steps:

• Confirm the Presealer and Sealer are completely dry, and the surface is clean, dust-free, and stable.
• Ensure good ventilation and avoid application below 10°C or above 25°C.
• Mix 2 parts Component A with 1 part Component B, stirring slowly until uniform.
• Let the mixture rest for 5 minutes before applying. Use only what can be applied within one session.
• Pour into a clean paint tray and apply a thin, even coat with a short-pile roller (4 mm) or brush. Avoid puddles or heavy build-up.
• Allow the first coat to dry for at least 4 hours, then mix a fresh batch and apply the second coat in the same way.
• The surface will be touch-dry within 4 hours and fully cured after 72 hours. Avoid water, cleaning, or heavy use during this time.
• Clean all tools immediately after use with a universal solvent cleaner and discard leftover mixed material.

Tips:

Apply in thin, even coats with good airflow. For long-term durability in floors, steps, exteriors, or pools, Heavy-Duty Sealer is the recommended finish.

Thoughtful planning ensures a smooth, consistent finish and helps prevent visible lines or uneven drying. Mas Maya Coating is a handcrafted material, so a considered approach makes all the difference.

Steps:

• Plan your workflow so each surface can be completed in one continuous session without stopping midway.
  
• Work in third order when possible: ceilings first, then walls, then floors — this prevents drips or debris from falling onto finished surfaces.
  
• When coating walls, work on opposite walls first to avoid touching wet areas.
  
• For floors, start from the farthest point and work back towards the door to avoid stepping on fresh material.
  
• If you need to step onto a slightly damp surface, use polystyrene boards to distribute your weight without marking the finish.
  
• Prepare all tools and materials in advance, and mix consistent batch sizes to maintain colour uniformity.
  
• Be mindful of lighting and airflow — direct sunlight or draughts can cause the surface to dry too quickly.
  
• For multi-day projects, mark clearly where you stopped so you can blend seamlessly when continuing.

Tips:

Have all materials ready — Primer, Mesh, Coating, and Sealers — and work methodically through each stage. A calm, well-planned process ensures a clean, even result every time.

Inside corners need extra attention for clean lines and a smooth transition between surfaces.

Key Guidelines:

• Apply Mas Maya Mesh right up to the corner edge on each side — never overlap or fold the mesh.
  
• Pull the coating gently away from the corner with the trowel to prevent build-up in the angle.
  
• Use a smaller flexible or plastic trowel to work cleanly into the corner.
  
• Once the coating is firm but not fully dry, mist lightly with water and use the Mas Maya Foam Float to bring up surface cream.
  
• Refine with a plastic trowel, pulling material away from the edge to keep the line neat and uncluttered.
  
• Apply two thin coats of Presealer once dry, followed by two coats of Sealer (as well as Heavy-Duty Sealer for exteriors).

Tips:

Work carefully and avoid overloading material in the joint. A light hand and clean tools ensure a crisp, seamless corner.

Outside corners benefit from a soft, curved edge for strength and durability while maintaining a smooth, seamless look.

Key Guidelines:

• Wrap Mas Maya Mesh fully around the corner, extending at least 10 cm onto each face.
  
• Avoid sharp edges — shape a gentle curve instead to reduce the risk of cracking.
  
• Use a flexible trowel to form and maintain a consistent curve along the edge.
  
• Once firm but not fully dry, mist lightly with water.
  
• To smooth the curve, hold a plastic bag tightly across both sides and move it up and down, or use a flexible plastic trowel.
  
• When fully dry, apply two thin coats of Presealer, followed by two coats of Sealer (or Heavy-Duty Sealer for exterior or high-traffic areas).

Tips:

Work with light pressure and consistent motion to keep the curve uniform. Avoid excess material at the edge — thinner, smoother layers create a stronger finish.

Curved areas — such as archways, rounded walls, columns, and curved corners — require a slower, more delicate approach. With the right tools and care, they showcase the natural softness and seamless quality of Mas Maya Coating.

Key Guidelines:

• Use flexible or curved trowels to follow the shape smoothly and maintain a consistent radius.
  
• Apply Mas Maya Mesh carefully around the curve while the coating is still wet, pressing it flat without folds or bubbles.
  
• Work in thinner layers than on flat walls to prevent cracking — around 2.5 mm for the base and 1.5–2 mm for the finish.
  
• Mist lightly with water as you shape and polish, but avoid over-wetting.
  
• Compress and refine the surface gently using circular or sweeping motions until the curve feels continuous and even.
  
• For tight or complex curves, use smaller strips of mesh for better control.
  
• Always apply two coats of both Presealer and Sealer (as well as Heavy-Duty Sealer for exteriors and high-traffic areas) for full protection.

Tips:

Patience and precision are key. Keep tools clean, layers thin, and movements smooth to achieve a flawless, flowing finish.

Small marks, scratches, or chips can be easily repaired using a little Mas Maya Coating and basic tools. This method is suitable for surface imperfections up to about 2–3 mm deep.

Key Guidelines:

• Clean the damaged area thoroughly and let it dry completely.
  
• Using a plastic spatula, press a small amount of Mas Maya Coating into the defect, ensuring full contact and no air pockets.
  
• Smooth the surface and remove any excess material while it’s still wet, keeping it level with the surrounding area.
  
• Once dry, sand lightly with 180–240 grit paper until smooth and flush. Wipe away dust.
  
• Apply two thin coats of Mas Maya Presealer, allowing each to dry fully.
  
• Finish with two thin coats of Mas Maya Sealer (as well as Heavy-Duty Sealer for high-use areas). Allow 72 hours before exposing to moisture or cleaning.

Tips:

Use a plastic spatula to avoid scratching nearby surfaces. Blend edges carefully and colour-match the coating for an invisible repair. For light surface scratches, sanding and resealing may be all that’s needed.

• Steel trowels (flat and flexible)
• Toothed trowel (5 mm)
• Plastic trowel (for detailing or curved areas)
• Short-pile roller (4 mm)
• Mixing paddle and bucket
• Spray bottle
• Mas Maya Foam Float
• Protective gear (mask, gloves, goggles)
• Low-adhesive masking tape
• Optional: moisture meter

Ceilings require a steady hand and thoughtful pacing. Working overhead means planning each step carefully to maintain an even, seamless surface while keeping comfort and control in mind.

Key Guidelines:

• Ensure the ceiling is clean, smooth, and free of dust or loose paint. Fill any cracks deeper than 3 mm with Mas Maya Prep and allow to dry fully.
  
• Apply Mas Maya Primer evenly with a short-pile roller or brush, avoiding puddles. Let it set for about one hour until slightly tacky.
  
• Mix Mas Maya Coating using 330 ml of water per 1 kg of powder (dissolve any pigment in the water first).
  
• Apply a 2.5 mm base layer with a trowel. Use Mas Maya Mesh if the ceiling has cracks, joins, or movement, pressing it gently into the fresh layer.
  
• Once the base layer is firm, apply a 1.5–2 mm finishing layer in smooth, overlapping strokes. Work methodically in smaller sections to maintain a wet edge.
  
• When the coating is firm but not dry, mist lightly with water and polish gently with a foam float or trowel to achieve a soft, even finish.
  
• Sealing is optional but recommended in moisture-prone areas. Apply two coats of Presealer followed by two coats of Sealer for added protection.
  

Tips:

• Use stable scaffolding or a secure platform to stay comfortable and maintain control.
  
• Keep lighting consistent to identify uneven spots as you work.
  
• Avoid overworking the material—ceiling layers dry faster than on walls.
  
• Work calmly and steadily. A smooth rhythm and clean tools are key to achieving a flawless, continuous finish.

Walls showcase the natural depth and movement of Mas Maya Coating. With the right preparation and rhythm, they achieve a seamless, tactile finish that feels both grounded and refined.

Key Guidelines:

• Make sure the surface is flat, smooth, and stable. Remove loose paint or weak plaster, and fill cracks deeper than 3 mm with Mas Maya Prep.
  
• Apply Mas Maya Primer evenly with a short-pile roller or brush, avoiding puddles. Let it set for about one hour until slightly tacky before applying the coating.
  
• Mix Mas Maya Coating with 330 ml of water per 1 kg of powder (dissolve pigment in the water first if using colour).
  
• Apply a 2.5 mm base layer using the toothed side of a 5 mm trowel. Where the wall has joints or movement, embed Mas Maya Mesh in the first layer, smoothing it just below the surface.
  
• Once the base layer is firm, apply a 1.5–2 mm finishing layer using a clean trowel and smooth, overlapping strokes. Work from top to bottom and maintain a wet edge for consistency.
  
• When the surface is firm but not fully dry, mist lightly with water and polish with a foam float in circular motions. Refine with a clean trowel to achieve the desired softness or sheen.
  
• Sealing is optional for dry interior walls, but recommended in areas exposed to moisture or stains. Apply two coats of Mas Maya Presealer followed by two coats of Mas Maya Sealer.

Tips:

• Work in manageable sections, finishing one area before moving to the next.
  
• Maintain steady, even pressure on the trowel to ensure a consistent texture.
  
• For artistic, clouded finishes, vary trowel strokes slightly and revisit areas while still damp.
  
• Keep the workspace evenly lit to spot imperfections early.
  
• Avoid direct sunlight or drafts during drying to prevent uneven colouration.
  
• Move calmly and confidently—Mas Maya Coating rewards patience and flow with a finish that feels effortless and organic.

Floors demand careful planning and patience. Because they’re subject to wear and movement, applying Mas Maya Coating requires thoughtful sequencing, reinforcement, and steady progress through the space.

Key Guidelines:

• Ensure the floor is level, smooth, and stable. Remove any dust, old paint, or adhesive residues, and fill cracks deeper than 3 mm with Mas Maya Prep.
  
• Apply Mas Maya Primer evenly with a short-pile roller or brush. Allow it to set for about one hour until slightly tacky before coating.
  
• Mix Mas Maya Coating using 400 ml of water per 1 kg of powder (dissolve pigment in water first if used).
  
• Begin with a 2.5 mm base layer using the toothed side of a 5 mm trowel. Press Mas Maya Mesh into this layer for reinforcement, overlapping sheets by 10 cm and keeping 1 cm from the edges. Smooth over the mesh until fully covered.
  
• Allow the base layer to dry until firm to the touch before applying the finishing layer.
  
• Apply a 1.5–2 mm finishing layer with a clean trowel, working methodically from the farthest corner of the room toward the door to avoid stepping on fresh material.
  
• When the coating is firm but not fully dry, mist lightly with water and polish with a foam float or trowel to refine the surface.
  
• Once dry, apply two coats of Mas Maya Presealer followed by two coats of Mas Maya Sealer. For high-traffic or commercial areas, finish with Mas Maya Heavy-Duty Sealer for maximum durability.

Tips:

• Plan your path before starting—always work toward the exit.
  
• Use lightweight XPS or polystyrene boards (at least 3.5 cm thick) to distribute weight when standing or kneeling on the surface once partially dry.
  
• Avoid dragging tools or boards to prevent scratches.
  
• Keep batch sizes consistent to ensure uniform colour.
  
• Allow 72 hours of curing before exposing the floor to moisture or heavy use.
  
• Maintain calm, deliberate movements throughout the process—the best floors come from rhythm and patience.

Pools require extra care and patience. Because they’re constantly exposed to water and temperature changes, the key to success is slow, even drying and proper sealing. With the right preparation, Mas Maya Coating creates a smooth, durable surface that feels natural underwater.

Key Guidelines:

• Ensure the pool structure is stable, dry, and fitted with an intact waterproof membrane before beginning. Repair cracks or joints with Mas Maya Prep and smooth the surface completely.
  
• Apply Mas Maya Pool Primer evenly with a brush or spray gun, covering all surfaces without puddles. Allow it to set for at least one hour until slightly tacky.
  
• While the primer is still tacky, embed Mas Maya Mesh across the surface, overlapping each section by 10 cm and keeping 1 cm from edges. Smooth the mesh gently into the primer.
  
• Mix Mas Maya Coating using 400 ml of water per 1 kg of powder (dissolve pigment in water first if used).
  
• Apply a 2.5 mm base layer over the mesh and smooth evenly. Let it dry until firm to the touch.
  
• Apply a 1.5–2 mm finishing layer with a clean trowel, working in smooth, overlapping strokes across walls and floors for a seamless result.
  
• Once the coating is firm but not dry, mist lightly with water and polish gently with a foam float or trowel to refine the surface.
  
• After full drying, apply one coat of Mas Maya Presealer followed by two coats of Mas Maya Sealer. For additional protection, finish with Mas Maya Heavy-Duty Sealer.

Tips:

• Start from the walls and work downward to the floor, avoiding stepping on freshly applied areas.
  
• Keep lighting consistent to spot imperfections early.
  
• Use smaller batches of coating for colour consistency and easier handling.
  
• Clean tools frequently to prevent marks or drag lines on the surface.
  
• Allow the coating to dry naturally and evenly — avoid forced drying or direct sunlight.
  
• Cover the pool loosely during drying (using a breathable tarp or shade cloth) to slow evaporation and protect from wind or sun exposure. This helps prevent the coating from drying too quickly, which can cause surface cracking.
  
• Allow the pool to cure fully for at least 7 days before filling it with water.
  

A steady rhythm and controlled environment are key — the slower the drying process, the stronger and more beautiful the final waterproof finish will be.

Bathrooms combine moisture, movement, and daily wear — so applying Mas Maya Coating here requires extra care to ensure a waterproof, spot-free finish. With proper sealing and attention to detail, the result is a calm, natural surface that performs beautifully in wet conditions.

Key Guidelines:

• Check that all surfaces are stable, dry, and fitted with a waterproof membrane beneath (especially around showers, baths, and wet zones).
  
• Repair any cracks or joints with Mas Maya Prep and smooth the surface completely.
  
• Apply Mas Maya Primer evenly with a short-pile roller or brush, ensuring full coverage without puddles. Allow it to set for about one hour until slightly tacky.
  
• Mix Mas Maya Coating using 330 ml of water per 1 kg of powder (dissolve pigment in the water first if used).
  
• Apply a 2.5 mm base layer using the toothed side of a 5 mm trowel. Where cracks or joins are present, embed Mas Maya Mesh while the layer is still wet. Smooth over until the mesh is fully covered.
  
• Once the base layer is firm, apply a 1.5–2 mm finishing layer with a clean steel trowel. Work in smooth, overlapping strokes to maintain a seamless texture.
  
• When the surface is firm but not dry, mist lightly with water and polish with a foam float or trowel to refine and close the pores.

Sealing:

• Bathrooms must always be sealed to prevent water absorption.
  
• Apply two coats of Mas Maya Presealer, ensuring full and even coverage. This layer helps preserve colour and prepare the surface for sealing.
  
• Follow with two coats of Mas Maya Sealer, using a clean short-pile roller. Make sure every area is sealed—if pores remain open, spotty water marks may appear when wet. These will fade as the coating dries, but full sealing prevents this effect entirely.
  
• For extra durability, especially on floors or shower interiors, finish with Mas Maya Heavy-Duty Sealer.

Tips:

• Maintain consistent lighting to easily spot unsealed or uneven areas.
  
• Keep all tools clean to avoid surface drag marks.
  
• Allow each layer to dry naturally; avoid fast drying or direct airflow.
  
• After sealing, let the coating cure for at least 7 days before exposing it to water.
  
• Work calmly and methodically—closing every pore and maintaining even layers ensures a flawless, waterproof finish that stays beautiful for years.

Furniture and basins showcase the versatility of Mas Maya Coating — turning everyday pieces into smooth, sculptural forms with a natural, tactile finish. Because these surfaces experience regular contact and water exposure, precision and sealing are essential for durability and protection.

Key Guidelines:

• Make sure the surface is clean, dry, and stable. Remove any grease, dust, or wax residues. For glossy or non-porous materials (like laminate or sealed wood), lightly sand the surface to create a better key for adhesion.
  
• Apply Mas Maya Primer evenly with a short-pile roller or brush, avoiding puddles. Allow it to set for about one hour until slightly tacky.
  
• Mix Mas Maya Coating using 330 ml of water per 1 kg of powder (dissolve pigment in the water first if used).
  
• Apply a thin 2.5 mm base layer using a small steel or plastic trowel. On areas prone to movement or with joints (like wood or composite), embed Mas Maya Mesh into this first layer for reinforcement. Smooth over until fully covered.
  
• Once firm, apply a 1.5–2 mm finishing layer, working carefully around edges and curves. Use smooth, overlapping strokes for an even finish.
  
• When the coating is firm but not fully dry, mist lightly with water and polish gently with a foam float or trowel to refine the texture and close pores.

Sealing:

• Always seal furniture and basins to protect against moisture, stains, and daily wear.
  
• Apply two coats of Mas Maya Presealer to prepare the surface and preserve colour.
  
• Follow with two coats of Mas Maya Sealer, ensuring full, even coverage—especially around corners, edges, and inner basins where water may collect.
  
• For countertops, washstands, or high-use pieces, finish with Mas Maya Heavy-Duty Sealer for maximum protection against abrasion and water exposure.

Tips:

• Keep layers thin and even to avoid build-up on edges and corners.
  
• Ensure all pores are fully closed before sealing—any open pores may cause temporary water spotting (which will fade as the surface dries, but can be avoided with complete sealing).
  
• Allow sealed pieces to cure for at least 7 days before regular use or water exposure.
  
• Avoid resting heavy objects or containers directly on the coating during curing.
  
• Work patiently and in good light—precision is key on smaller surfaces to achieve that seamless, stone-like quality Mas Maya Coating is known for.